Call Us (480) 795-7199

Radium engineering fuel pump relay and wiring kit

Sale!

Original price was: $109.95.Current price is: $89.95.

Complete your kit

TI Automotive brushless fuel pump and controller

From TI Automotive:

TI Automotive's new in-tank brushless fuel pump utilizes advanced technology for maximum reliability and efficiency. The result is a next-generation pump for any type of engine offering precise control of fuel pressure, lower current draw, reduced heat and less noise.
Supporting up to 1000+ HP, the BKS1000 provides more power, more torque and more speed. Matched controller with simple power and ground operations for easy maintainability. The controller features sealed electronics for weather resistance.

Fuel: GAS or FLEX
Horsepower: 1000
Flow Rate (lph): 550
Pressure (psi): 40

 

Radium Engineering Brushless Fuel Pump Hanger for R35 Nissan GTR

Directly From Radium:

The Radium Engineering fuel hanger completely replaces the factory in-tank fuel pump unit in the R35 GT-R and permits up to three 39mm diameter aftermarket pumps (brushed or brushless) to supply fuel to the engine. No permanent vehicle modifications are required for installation. The pumps are housed in an aluminum collector box that is kept full during operation. This ensures that fuel starvation does not occur, even during aggressive driving. The fuel pump outlet port is -10AN ORB female threaded and includes a 6AN male adapter, while the return port is -8AN ORB female threaded and includes a 6AN male adapter. The system is compatible with alternative fuels such as methanol, ethanol, E85, etc. Radium Engineering recommends reviewing the installation instructions (link above) before purchasing.

 

From ATR Performance:

ATR is located in the Phoenix area, and as such - We experience very warm temperatures (Often in excess of 110 degrees F).  We've run every different variety of fuel pump and hanger setups and found flaws in most.  The R35 fuel tank is located above the transmission and exhaust, and fuel is known to get quite warm in the summer months.  In addition to this, many brushed pumps such as the Walbro 450 and 525 heat the fuel even more.  In fact, ethanol can get hot enough to boil inside the R35 fuel tank.  This results in fuel cavitation, engine cutting out, and eventual fuel pump failure.  When we installed this Radium hanger with two Walbro branded BRUSHLESS fuel pumps and controllers, we were able to cut the fuel temps by a minimum of 15 degrees F and have never experienced a fuel pump failure in over 3 years of use with this setup.

Fitted with two Walbro BKS1001 brushless fuel pumps, this Radium hanger will support 1500HP while running on E85 ethanol.  Please NOTE that this hanger does NOT come with fuel pumps or fuel pump wiring - We sell these items separately.

Description

From Radium:

This Do-It-Yourself wiring kit includes the necessary parts to construct a power wiring harness for one fuel pump. It uses the highest quality components to ensure proper operation in all conditions. The relay and fuse holder are sealed to allow installation in weather exposed areas if necessary. Aircraft grade TXL wiring is resistant to all chemicals and elevated temperatures. Raychem crimpless solder-based butt connectors make reliable wire connections easy and clean.

From ATR Performance:

We wanted a cost effective alternative to the problematic Visconti hardwire kit, and opted for this high quality product from Radium Engineering.  You’ll want to purchase two of these to complete your Radium hanger with Dual TI Automotive brushless fuel pumps, to feed up to 1500HP on E85 ethanol.  We wire these directly off the battery, through the firewall, and to the passenger interior B panel cover for a clean and accessible install right next to your brushless controllers and fuel pumps.  Please message us for more specific install info

Additional information

Weight 2 lbs
Dimensions 11 × 7 × 3 in

Reviews

There are no reviews yet.

Be the first to review “Radium engineering fuel pump relay and wiring kit”

Your email address will not be published. Required fields are marked *